©2009-2010 Dynojet Research, Inc. All Rights Reserved.
2004-2006 Subaru Impreza WRX STi 2.5L - CMD-1011 - Installation Instructions
This manual is copyrighted by Dynojet Research, Inc., hereafter referred to as Dynojet,
and all rights are reserved. This manual, as well as the software described in it, is
furnished under license and may only be used or copied in accordance with the terms of
such license. This manual is furnished for informational use only, is subject to change
without notice, and should not be construed as a commitment by Dynojet. Dynojet
assumes no responsibility or liability for any error or inaccuracies that may appear in this
manual. Except as permitted by such license, no part of this manual may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, recording, or otherwise, without the prior written permission of Dynojet.
The Dynojet logo is a trademark of Dynojet Research, Inc.
Any trademarks, trade names, service marks, or service names owned or registered by any
other company and used in this guide are the property of their respective companies.
Dynojet Research, Inc., 2191 Mendenhall Drive, North Las Vegas, Nevada 89081, USA.
Printed in USA.
Part Number: ICMD-1011 Version 04 (04/2010)
PARTS LIST
quantity description
1 CMD Module
1 Dynojet Master Control Center Software
1 Instruction Manual
1 Registration Card
1 CMD Plug & Play Harness
1 Dynojet CAN-Link Cable
1 USB COM Cable
2 CAN Port Seals
1 USB Port Seal
2 Dual Lock Fasteners
6 Zip Ties
1 Alcohol Swab
TOOLS REQUIRED
• 10mm socket with ratchet
• 10mm combination wrench
• zip tie cutters
• flat blade screwdriver
OVERVIEW: CMD MODULE
status LED
main wiring harness
connection
CAN ports
USB port
ICMD-1011.04 2004-2006 Subaru Impreza WRX STi 2.5L - CMD-1011- 1
OVERVIEW: VEHICLE
boost control solenoid and
intermediate connector E1
ground bolt
Figure A Figure B Figure C
MAF
intermediate connectors
E2 and E3
ground bolt
negative post
1 Using a 10mm socket with ratchet, loosen the
nut and remove the negative battery cable
from the negative post of the battery.
2 Using a 10mm socket with ratchet, remove the
grounding bolt from the inner fender.
This grounding bolt is located on the drivers’
inner fender behind the battery as shown in
Figure B.
3 Using a 10mm wrench, remove the bolt
holding the fuse box to the inner fender.
ICMD-1011.04
2004-2006 Subaru Impreza WRX STi 2.5L - CMD-1011 - 2
4 Locate the two front wiring harness plugs E2
and E3.
The E2 and E3 plugs are located below the
fuse box.
5 Disconnect the E2 and E3 plugs.
Figure D Figure E Figure F
6 Attach the female connectors from the CMD
harness to the two front wiring harness plugs
E2 and E3.
7 Attach the male connectors from the CMD
harness to the stock connectors.
zip ties
wiring harness
8 Reinstall the fuse box using the bolt removed
earlier.
9 Bolt the ground wire from the CMD harness to
the grounding bolt on the drivers' inner
fender.
10 Route the CMD wiring harness around the
back of the engine, across the A/C lines, and
over to the boost control solenoid location.
Zip ties are provided for a clean installation.
ICMD-1011.04
2004-2006 Subaru Impreza WRX STi 2.5L - CMD-1011 - 3
19 Locate a suitable mounting location for the CMD module. Note: Leave the two connectors on the side of the CMD accessible. This allows you to easily connect to the CMD for programming without having to disturb its mounting location. The CMD module fits nicely beside the fuse box as shown in Figure M. Your mounting location may vary.
Get the file: Download here | Type PDF
19 Locate a suitable mounting location for the CMD module. Note: Leave the two connectors on the side of the CMD accessible. This allows you to easily connect to the CMD for programming without having to disturb its mounting location. The CMD module fits nicely beside the fuse box as shown in Figure M. Your mounting location may vary.
Get the file: Download here | Type PDF